Sharp 2216 service manual

E : Unit parts recommended to be stocked for efficient after sales service. S : Consumable parts. A Rank : The parts which may be with the revolution or loading. For U. SF Exteriors 1 NO. Kingdom 3. SF 1 Exteriors. SF 2 Operation panel section NO. SF 6 1 Optical unit 1 NO. SF 7 2 Optical unit 2 NO. SF 8! SF 15 64 19 1 16 18 17 1. You can only view or download manuals with. Lower separation pawl replacement. Optical system.

Main charger MC unit. Process section. Process unit. Drum Replace every 60K copies. Blank lamp unit Clean every 60K copies. Discharge lamp unit Clean every 60K copies.

Cleaner blade Replace every 60K copies. Drum separation pawl Replace every 60K copies. Toner reception seal Replace every 60K copies. DB blade replacement Replace every K copies. V ring attachment. Note for toner hopper drive gear 31T and stirring shaft attachment. Frame major parts.

Cooling fan motor replacement. Power unit. Tray size detecting PWB. Main PWB unit. AC power PWB. Ozone filter Check every 60K copies, and clean every K copies. Multi paper feed unit. Developing doctor clearance adjustment.

Developing magnet roller main pole position adjustment. Adjustment items. Note for adjustments. Adjustment of each section. Lens reference position adjustment.

Vertical copy magnification ratio adjustment. Resolution adjustment Focus adjustment. Horizontal copy magnification ratio adjustment. Comparison table of lens values and simulation input values. Vertical skew adjsutment.

Horizontal skew adjustment. Exposure balance adjustment. Copy lead edge adjustment. Copy density adjustment. Process section adjustment. Operating procedure. List of simulations. Details of simulations. User simulation. Maintenance cycle and maintenance items. System block diagram. Main circuit. Supply parts U. Power source Supplied from the copier's power section.

Weight 8. Including mounted fittings] Power source Supplied from the copier. DC24V 1. Power consumption Max. Staple section Type Copier stapler Stapling time 1. Binding reference Front reference Staple supply Cartridge 5, pcs. External view and internal structure 5 6 1 4 2 7 8 3 9 10 4 11 12 14 15 16 13 No. Name No. Clutches, solenoids, and motors 6 8 9 7 11 1 12 3 2 5 10 4 Clutches and solenoids No.

DC brushless. Name 1 No. Installation Installing conditions The surrounding conditions of the machine affect the machine performance greatly. If dust enters the machine, malfunctions may occur. Keep the machine in level state to maintain the performance. Also allow enough space around the machine for proper operation. Optical system lock release A. Mirror unit fixing screw B. Mirror unit fixing screw Paper feed tray Lens fixing screw.

Charger cleaning A. Main charger unit electrode cleaning 1 Press the hook section of the main charger unit to release lock, and pull out and remove the main charger unit from the copier. Hook main charger unit 2 Remove one fixing screw of the main charger unit on the back side. Fixing screw Electrode section Main charger unit 3 Press the electrode cleaner onto the tips of the electrode so that the tips are inserted into the cleaner a few times to clean.

Electrode cleaner Electrode section. Main charger unit 5. Developing unit setting A. Developing unit setting 1 Open the front cabinet, remove the installation toner fixed to the developing unit level with tape, and pull the developing unit lever toward you.

Hand carry strap DV lever Developing unit Grip. Fixing screw Fixing screw Toner hopper Developing unit 4 While supplying developer from the developer supply port of the developing unit, turn the MG gear clockwise with a screwdriver or a scale to supply fully in the developing unit. Fixing screw Toner hopper Fixing screw Developing unit. Hand carry strap Developing unit Grip 7 Close the developing unit lever and close the front cabinet. Developing unit lever Front cabinet With the above procedure, setting of the developing unit is completed.

Toner density sensor level adjustment Turn on the copier power switch. Developing unit level adjustment 1 Execute simulation C 0 2 5 2 2 After 3 minutes, simulation 25 is completed. Accessory installation A. Copier tray installation Install the copy tray to the paper exit section on the left side of the copier.

Copy tray 8. Toner supply 1 Open the front cabinet. Toner cartridge 4 or 5 times 4 To install the toner cartridge, insert the projection of the cartridge into the hole on the front of the developer unit as shown to unlock the toner hopper cover. Sealing tape G Close the toner hopper cover.

H Slide the developing unit into the copier. Center shift adjustment There is basically no need to perform the center shift adjustment because it is made when shipping. Section b Section b Section a Direction A Section a Direction B Note When fixing the cassette cabinet, the fixing screws and the cabinet clearance a and b are in symmetry.

Label attachment A. Label attachment Attach the magnification ratio select label packed together with the Operation manual to the position shown in the figure below.

Paper feed section 1 General descriptions To realize the compact design, the front loading system and the foldable multi paper feed unit Option for some areas are employed. SF 50 Sheets sheets The paper feed tray is of the universal type and has capacity of sheets. Manual paper feed is made in the multi paper feed.

Roller release arm Take-up roller Paper feed roller Paper feed roller shaft When the CPFC turns off, rotation stops and the take-up roller is pushed up to the original position by the roller release arm spring. Manual paper feed operation There is no special mechanism for manual paper feed other than the manual feed paper sensing actuator and the paper guide.

Developing section 1 General descriptions 1 Two-component developer The developer is composed of toner and carrier.

Viewed from the rear of develoing unit DV harness connector. Name 1 Magnet roller Forms a magnetic brush of carrier by magnetic force.

The original is set in the left center position. The copy lamp unit and the No. The No. The output signal of this sensor is the basic signal to control the copy magnification ratio. Mirror base scan speed is changed for zooming Enlargment Normal Zooming by changing the lens and mirror position Original Reduction Copy direction. Parts identification and functions Mirror home position sensor No. Mirror base wire Temperature fuse. It is scanned by the mirror motor.

The element is photo diodes. The distance between the lens and the exposure surface of the drum is shorter. Then divide the difference between the voltages of EX1. Optical system dirt correction This model perform dirt correction by changing the copy lamp intensity according to the dirt degree in the optical system the copy lamp unit, No.

The reference value is the AE sensor output value which is obtained when the reference plate is exposed with the copy lamp voltage of This value is checked with sim , CLV Sim46 Automatic exposure sensor CPU reference value setting 1 Clean the optical system at every maintenance. Select a date. Where can I find my model number?

All Sharp products have a model number stated on them, some in more than one place. The model number can be found on the original box the item was purchased in, on the product manual, and on the product in the locations described below. Helpful tip: For convenience, if you have a digital camera or smart phone, you may want to take a digital photo of the model number. TV On the back of the TV on a sticker that shows a bar code and serial number.

Audio Systems. Sound Bars. PCI Air Purifiers. Where can I find my serial number? All Sharp products have a serial number stated on them, some in more than one place. The serial number can be found on the original box the item was purchased in, on the product manual, and on the product in the locations described below. Service Request.

Contact Information. Address Address 1 is Required. Address 2.